How To Install And Use Coolbits Overclock

Need to squeeze some extra juice out of your Nvidia video card? Want that extra FPS in your favourite shooter to secure your rank? The process is extremely simple and all you need to do is enable Coolbits which is popular in Windows. This tutorial can be done by any user who has some simple knowledge of the terminal and this should work with nearly any release of the nvidia’s unix drivers for the past year or so.

  1. How To Install And Use Coolbits Overclock Windows 10
  2. How To Install And Use Coolbits Overclock Windows 7
  3. How To Install And Use Coolbits Overclock Software

To start off be sure to have Nvidia’s drivers installed and working properly. Next go into terminal and make sure you are root (and for Ubuntu users simply follow the commands I do as I am using Ubuntu Gutsy). Open your favourite text editor, for me it is Nano due to its simplicity.

sudo nano /etc/X11/xorg.conf

Look for a section of code named “Device.” It should resemble something similar to this.

Section “Device”
Identifier “Videocard0”
Driver “nvidia”
VendorName “Videocard vendorname”
BoardName “nVidia Corporation Unknown device 0000”
EndSection

Now all you need to do is add this piece of code towards the end of the section.

Option “Coolbits” “1”

However, does this CoolBits Linux port offer the reliability of its Windows counterpart and fix the issues that NVClock has yet to address? Today we have a short guide on how to enable CoolBits with these new NVIDIA drivers (1.0-7664), how to change your core and memory speeds, and the results we obtained when using the CoolBits utility. I have enabled nvidia x server overclock settings using coolbits. Is an few strange that using coolbits using an option value not is possbile enable both fan and overclock settings at same time. When selecting coolbits to enable overclock settings allways that starting the system the previous overclock or underclock settings not are saved.

Now your xorg.conf should look like this.

Section “Device”
Identifier “Videocard0”
Driver “nvidia”
VendorName “Videocard vendorname”
BoardName “nVidia Corporation Unknown device 0000”
Option “Coolbits” “1”
EndSection

Save the file and exit out of terminal. Now you are all done, all you must do is restart X by restarting your machine or entering the following code in the terminal.

init 3 && init 5

Coolbits will now be located within the Nvidia Display Settings application. Good luck and if you have any questions or comments, please leave them below with your email address included (it will not be displayed, it is just for me to reply to your question).

I want to overclock my graphics card but i dont know what program to use. I have a gigabyte 6600gt pcie card, do i use coolbits or do i use riva tuner which one is better? My rig amd 3500+ venice nforce 4 sli mobo 1 gb ram 120 gb hdd 6600gt pcie.

*Disclaimer: This tutorial is only for demonstrational purposes only. This tutorial is distributed in the hope that it will useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Use at your own risk.

< NVIDIA

Fixing terminal resolution

Transitioning from nouveau may cause your startup terminal to display at a lower resolution.

For GRUB, see GRUB/Tips and tricks#Setting the framebuffer resolution for details.

For rEFInd, add to esp/EFI/refind/refind.conf and /etc/refind.d/refind.conf (latter file is optional but recommended):

A small caveat is that this will hide the kernel parameters from being shown during boot.

Using TV-out

A good article on the subject can be found here.

X with a TV (DFP) as the only display

The X server falls back to CRT-0 if no monitor is automatically detected. This can be a problem when using a DVI connected TV as the main display, and X is started while the TV is turned off or otherwise disconnected.

To force NVIDIA to use DFP, store a copy of the EDID somewhere in the filesystem so that X can parse the file instead of reading EDID from the TV/DFP.

To acquire the EDID, start nvidia-settings. It will show some information in tree format, ignore the rest of the settings for now and select the GPU (the corresponding entry should be titled 'GPU-0' or similar), click the DFP section (again, DFP-0 or similar), click on the Acquire Edid Button and store it somewhere, for example, /etc/X11/dfp0.edid.

If in the front-end mouse and keyboard are not attached, the EDID can be acquired using only the command line. Run an X server with enough verbosity to print out the EDID block:

After the X Server has finished initializing, close it and your log file will probably be in /var/log/Xorg.0.log. Extract the EDID block using nvidia-xconfig:

Edit xorg.conf by adding to the Device section:

The ConnectedMonitor option forces the driver to recognize the DFP as if it were connected. The CustomEDID provides EDID data for the device, meaning that it will start up just as if the TV/DFP was connected during X the process.

This way, one can automatically start a display manager at boot time and still have a working and properly configured X screen by the time the TV gets powered on.

If the above changes did not work, in the xorg.conf under Device section you can try to remove the Option 'ConnectedMonitor' 'DFP' and add the following lines:

The NoDFPNativeResolutionCheck prevents NVIDIA driver from disabling all the modes that do not fit in the native resolution.

Check the power source

The NVIDIA X.org driver can also be used to detect the GPU's current source of power. To see the current power source, check the 'GPUPowerSource' read-only parameter (0 - AC, 1 - battery):

Listening to ACPI events

NVIDIA drivers automatically try to connect to the acpid daemon and listen to ACPI events such as battery power, docking, some hotkeys, etc. If connection fails, X.org will output the following warning:

While completely harmless, you may get rid of this message by disabling the ConnectToAcpid option in your /etc/X11/xorg.conf.d/20-nvidia.conf:

If you are on laptop, it might be a good idea to install and enable the acpid daemon instead.

Displaying GPU temperature in the shell

There are three methods to query the GPU temperature. nvidia-settings requires that you are using X, nvidia-smi or nvclock do not. Also note that nvclock currently does not work with newer NVIDIA cards such as GeForce 200 series cards as well as embedded GPUs such as the Zotac IONITX's 8800GS.

nvidia-settings

To display the GPU temp in the shell, use nvidia-settings as follows:

This will output something similar to the following:

The GPU temps of this board is 41 C.

In order to get just the temperature for use in utilities such as rrdtool or conky:

nvidia-smi

Use nvidia-smi which can read temps directly from the GPU without the need to use X at all, e.g. when running Wayland or on a headless server. To display the GPU temperature in the shell, use nvidia-smi as follows:

This should output something similar to the following:

Only for temperature:

How To Install And Use Coolbits Overclock

In order to get just the temperature for use in utilities such as rrdtool or conky:

Reference: http://www.question-defense.com/2010/03/22/gpu-linux-shell-temp-get-nvidia-gpu-temperatures-via-linux-cli.

nvclock

Use nvclockAUR which is available from the AUR.

Note:nvclock cannot access thermal sensors on newer NVIDIA cards such as Geforce 200 series cards.

There can be significant differences between the temperatures reported by nvclock and nvidia-settings/nv-control. According to this post by the author (thunderbird) of nvclock, the nvclock values should be more accurate.

Overclocking and cooling

Enabling overclocking

Warning: Overclocking might permanently damage your hardware. You have been warned.

Overclocking is controlled via Coolbits option in the Device section, which enables various unsupported features:

Tip: The Coolbits option can be easily controlled with the nvidia-xconfig, which manipulates the Xorg configuration files:

The Coolbits value is the sum of its component bits in the binary numeral system. The component bits are:

  • 1 (bit 0) - Enables overclocking of older (pre-Fermi) cores on the Clock Frequencies page in nvidia-settings.
  • 2 (bit 1) - When this bit is set, the driver will 'attempt to initialize SLI when using GPUs with different amounts of video memory'.
  • 4 (bit 2) - Enables manual configuration of GPU fan speed on the Thermal Monitor page in nvidia-settings.
  • 8 (bit 3) - Enables overclocking on the PowerMizer page in nvidia-settings. Available since version 337.12 for the Fermi architecture and newer.[1]
  • 16 (bit 4) - Enables overvoltage using nvidia-settings CLI options. Available since version 346.16 for the Fermi architecture and newer.[2]

To enable multiple features, add the Coolbits values together. For example, to enable overclocking and overvoltage of Fermi cores, set Option 'Coolbits' '24'.

The documentation of Coolbits can be found in /usr/share/doc/nvidia/html/xconfigoptions.html and here.

Note: An alternative is to edit and reflash the GPU BIOS either under DOS (preferred), or within a Win32 environment by way of nvflash[dead link 2020-04-01 ⓘ] and NiBiTor 6.0[dead link 2020-04-01 ⓘ]. The advantage of BIOS flashing is that not only can voltage limits be raised, but stability is generally improved over software overclocking methods such as Coolbits. Fermi BIOS modification tutorial

Setting static 2D/3D clocks

Set the following string in the Device section to enable PowerMizer at its maximum performance level (VSync will not work without this line):

Allow change to highest performance mode

The factual accuracy of this article or section is disputed.

Reason: This section refers to the limits for GPU boost, which is unrelated to overclocking discussed above. The nvidia-smi(1) man page says that it is 'For Tesla devices from the Kepler+ family and Maxwell-based GeForce Titan.' And as far as Lahwaacz is aware, the only GPU which supports this and does not have the default clocks equal to the maximum, is Tesla K40 [3]. Since the Pascal architecture, Boost 3.0 handles automatic clocking even differently. (Discuss in Talk:NVIDIA/Tips and tricks#)

Since changing performance mode and overclocking memory rate has little to no effect in nvidia-settings, try this:

  • Setting Coolbits to 24 or 28 and remove Powermizer RegistryDwords -> Restart X
  • find out max. Clock and Memory rate. (this can be LOWER than what your gfx card reports after booting!):
  • set rates for GPU 0:

After setting the rates the max. performance mode works in nvidia-settings and you can overclock graphics-clock and memory transfer rate.

Saving overclocking settings

Typically, clock and voltage offsets inserted in the nvidia-settings interface are not saved, being lost after a reboot.Fortunately, there are tools that offer an interface for overclocking under the proprietary driver, able to save the user's overclockingpreferences and automatically applying them on boot. Some of them are:

  • gweAUR - graphical, applies settings on desktop session start
  • nvclockAUR and systemd-nvclock-unitAUR - graphical, applies settings on system boot
  • nvocAUR - text based, profiles are configuration files in /etc/nvoc.d/, applies settings on desktop session start

Custom TDP Limit

Modern Nvidia graphics cards throttle frequency to stay in their TDP and temperature limits. To increase performance it is possible to change the TDP limit, which will result in higher temperatures and higher power consumption.

For example, to set the power limit to 160.30W:

To set the power limit on boot (without driver persistence):

Set fan speed at login

This article or section needs language, wiki syntax or style improvements. See Help:Style for reference.

Reason: Refer to #Enabling overclocking for description of Coolbits. (Discuss in Talk:NVIDIA/Tips and tricks#)

You can adjust the fan speed on your graphics card with nvidia-settings' console interface. First ensure that your Xorg configuration has enabled the bit 2 in the Coolbits option.

Note: GeForce 400/500 series cards cannot currently set fan speeds at login using this method. This method only allows for the setting of fan speeds within the current X session by way of nvidia-settings.

Place the following line in your xinitrc file to adjust the fan when you launch Xorg. Replace n with the fan speed percentage you want to set.

You can also configure a second GPU by incrementing the GPU and fan number.

If you use a login manager such as GDM or SDDM, you can create a desktop entry file to process this setting. Create ~/.config/autostart/nvidia-fan-speed.desktop and place this text inside it. Again, change n to the speed percentage you want.

Note: Before driver version 349.16, GPUCurrentFanSpeed was used instead of GPUTargetFanSpeed.[4]

To make it possible to adjust the fanspeed of more than one graphics card, run:

Note: On some laptops (including the ThinkPad X1 Extreme and P51/P52), there are two fans, but neither are controlled by nvidia.

Kernel module parameters

This article or section needs language, wiki syntax or style improvements. See Help:Style for reference.

Reason: Giving advanced examples without explaining what they do is pointless. (Discuss in Talk:NVIDIA/Tips and tricks#)

Some options can be set as kernel module parameters, a full list can be obtained by running modinfo nvidia or looking at nv-reg.h. See the Gentoo wiki as well.

How To Install And Use Coolbits Overclock Windows 10

For example, enabling the following will turn on kernel mode setting (see above) and enable the PAT feature [5], which affects how memory is allocated. PAT was first introduced in Pentium III [6] and is supported by most newer CPUs (see wikipedia:Page attribute table#Processors). If your system can support this feature, it should improve performance.

On some notebooks, to enable any nvidia settings tweaking you must include this option, otherwise it responds with 'Setting applications clocks is not supported' etc. Raphael saadiq stone rollin 2011 rar download.

Preserve video memory after suspend

This article or section needs language, wiki syntax or style improvements. See Help:Style for reference.

Reason: See Help:Style and Help:Style/Formatting and punctuation. (Discuss in Talk:NVIDIA/Tips and tricks#)

By default the NVIDIA Linux drivers save and restore only essential video memory allocations on system suspend and resume. Quoting NVIDIA ([7], also available with the nvidia-utils package in /usr/share/doc/nvidia/html/powermanagement.html): The resulting loss of video memory contents is partially compensated for by the user-space NVIDIA drivers, and by some applications, but can lead to failures such as rendering corruption and application crashes upon exit from power management cycles.

This article or section needs expansion.

How To Install And Use Coolbits Overclock Windows 7

Reason: Why is it 'still experimental' and where is it documented? (Discuss in Talk:NVIDIA/Tips and tricks#)

The new, still experimental, system enables saving all video memory (given enough space on disk or main RAM). The interface is through the /proc/driver/nvidia/suspend file as follows: write 'suspend' (or 'hibernate') to /proc/driver/nvidia/suspend immediately before writing to the usual Linux /sys/power/state file, write 'resume' to /proc/driver/nvidia/suspend immediately after waking up, or after an unsuccessful attempt to suspend or hibernate.

The NVIDIA drivers rely on a user defined file system for storage. The chosen file system needs to support unnamed temporary files (ext4 works) and have sufficient capacity for storing the video memory allocations (e.g., at least (sum of the memory capacities of all NVIDIA GPUs) * 1.2). Use the command nvidia-smi -q -d MEMORY to list the memory capacities of all GPUs in the system.

To choose the file system used for storing video memory during system sleep (and change the default video memory save/restore strategy to save and restore all video memory allocations), it is necessary to pass two options to the 'nvidia' kernel module. For example, write the following line to /etc/modprobe.d/nvidia-power-management.conf and reboot:

Replace '/tmp-nvidia' in the previous line with a path within your desired file system.

The interaction with /proc/driver/nvidia/suspend is handled by the simple Unix shell script at /usr/bin/nvidia-sleep.sh, which will itself be called by a tool like Systemd. The Archlinux nvidia-utils package ships with the following relevant Systemd services (which essentially just call nvidia-sleep.sh): nvidia-suspend, nvidia-hibernate, nvidia-resume. Contrary to NVIDIA's instructions, it is currently not necessary to enable nvidia-resume (and it's in fact probably not a good idea to enable it), because the /usr/lib/systemd/system-sleep/nvidia script does the same thing as the service (but slightly earlier), and it is enabled by default (Systemd calls it after waking up from a suspend). Do enable nvidia-suspend and/or nvidia-hibernate.

Driver persistence

How To Install And Use Coolbits Overclock Software

Nvidia has a daemon that can be optionally run at boot. In a standard single-GPU X desktop environment the persistence daemon is not needed and can actually create issues [8]. See the Driver Persistence section of the Nvidia documentation for more details.

To start the persistence daemon at boot, enable the nvidia-persistenced.service. For manual usage see the upstream documentation.

Retrieved from 'https://wiki.archlinux.org/index.php?title=NVIDIA/Tips_and_tricks&oldid=641214'